assembly instructions three drawer three doos buffet christmas tree shops

Loading...

Malibu - 3 Drawer Filer

Assembly Instructions - Please keep for future reference		279/6288
		258/3422

Dimensions

Width - 40cm

Depth - 49cm

Height - 72.5cm

MADE IN BRITAIN

Important - Please read these instructions fully before starting assembly

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 4 - 30/06/14

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 17kgs. Please lift with care.

• Check you have all the components and tools listed on pages 1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the

use of power

drill/drivers for inserting screws,

as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth	• From time to time check that	• This product should not be
and mild detergent, do no use	there are no loose screws on	discarded with household
bleach or abrasive cleaners.	this unit.	waste. Take to your local
		authority waste disposal centre.

Tools required

Rule	Cross head	Scissors	Hammer	Eye protection	Electric drill
				(when using a	(only use when
	screwdriver			hammer or drill)	drilling into walls)

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

1

If you have damaged or missing components, call the

Components - Panels Customer Helpline: 08456 400800 quoting the reference numbers below

Please check you have all the panels listed below

3 Top (D2792A)

(397 x 490mm)

1	Left Side (D2793A)		2	Right Side (D2794A)		4	Rail (D2796A)
	(706 x 444mm)			(706 x 444mm)			(362 x 80mm) x 2

5	Drawer Front (D2797A)	6	Left Drawer Side (W370-124LH)	7	Right Drawer Side (W370-124RH)
	(358 x 156mm) x 2		(370 x 124mm) x 2		(370 x 124mm) x 2

	Drawer Back (W331-124)
8
	(331 x 124mm) x 2			Drawer Base (T342-367)			10	File Front (D2798A)
			9
				(342 x 367mm) x 2				(358 x 300mm)

11	File Back (D2795A)	12	File Side (W414)
	(338 x 253mm)		(314 x 120mm) x 2
				13	File Base (T320-320)
					(325 x 320mm)

14 Back (X807)

(390 x 650mm)

15 File Bar (FBAR334)

(334mm long) x 2

2

If you have damaged or missing components, call the

Components - Fittings Customer Helpline: 08456 400800 quoting the reference numbers below

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A		B			C
Wooden dowel (F22) x 6		Metal dowel (F901)	x 10			(F631) x 3
D		E			F
Nail (F51) x 14		Large locking			Small locking
		nut (F900)		x 2	nut (F3) x 8
G		H			I
40mm Screw (F910)	x 4	25mm Screw (F50) x 3			13mm Screw (F52)	x 6
J		K			L
13mm Screw (F63)	x 6	15mm Screw (F116) x 2			9mm Screw (F73) x 8
M					N
Drawer runner (F1004) x 4					Wedgefix (F639) x 4
O		P			Q
Knock-in Peg (F171GY) x 8		9mm Screw (F74)	x 4		Wedge panel holder
					(F248)	x 2
R a					S
		L Runner (F159) x 1
R b					Plastic Nail (F91) x 4
		R Runner (F160) x 1
R c
		L Runner (F161) x 1
R d
		R Runner (F162) x 1

Ruler - Use this ruler to help correctly identify the screws

mm	10	20	30	40	50	60	70	80	90	100	110	120	130	140	150	160	170

3

If you have damaged or missing components, call the

Assembly Instructions Customer Helpline: 08456 400800 quoting the reference numbers below

Step 1

Prepare the 2 drawer fronts

Screw 2 metal dowels B into each of the drawer fronts 5 .

Note: Tighten the metal dowels up fully against the panels.

Step 2

Prepare the drawer sides

Insert a small locking nut F into the hole shown on the left drawer side 6 and the right drawer side 7 .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the drawer fronts

Push the left drawer sides

. 6 and right drawer sides

. 7 onto the back of the drawer fronts 5 .

Turn the small locking nuts F on the left drawer side 6 and right drawer side 7 .

Note: Turn the locking nuts F clockwise to secure panels - more than 1/2 a turn.

4

barnesthesustrach.blogspot.com

Source: https://manualmachine.com/argos/malibu3drawerfiler/5831573-assembly-instructions/

Share this post